Chernovaya Repair - the basis on which it depends on how long the apartment will serve you after the completion of all repair and finishing works. This is a complete preparation of surfaces - floor, walls, ceiling - to finishing, this is the demolition and construction of partitions, work on the device of communications, wiring.
Redecorating
Cosmetic repair is, first of all, finishing works. The purpose of such a repair is to give a fresh appearance of the room and eliminate small defects and traces of operation that appeared from the time of previous repairs. At the same time, cosmetic repairs does not include, as a rule, neither the replacement of communications or redevelopment solutions.
Overhaul
Overhaul is perhaps the most thorough of all repairs. It implies redevelopment, if this thought, replacing obsolete communications, electrical work. Among other things, this is the complete preparation of all surfaces, and the decoration of the room. In short, the capital update of your apartment.
Designer repair
Designer repairs - differs from the capital of the large volume of designer work and copyright for the compliance of the design project approved by the customer. Often, designer repairs includes non-standard solutions for redevelopment, shift zoning, exclusive decor.
P-111M - a modern series of panel houses, designed specifically for the needs of the Ministry of Defense, in a number of sources appears the name of P-111mo, and in separate military projects - KPD-111M. Designed in the mid-1990s. Years of construction: from 1996 to the present. Total built about 280 houses. In Moscow, the house of the Typical series P-111M was built in microdistricts: Printers, Biryulyo, Zhulebino, Nikulino, Khodynskoye, Kuntsevo, Goljanovo, Textiles, Lublin and South Butovo. As a rule, the houses of this series are built on the former lands of the Ministry of Defense, in a number of other areas of Moscow (Konkovo, Zyuzino) at home of the 111m series are built point. Currently, in Moscow, the houses of this series are not built in Moscow.
In the suburbs of the new buildings of the P-111m series built / are built in cities: Balashikha, Voskresensk, Golitsyno, Dedovsk, Dmitrov, Dolgoprudny, Domodedovo, Dresna, Railway, Zvenigorod, Klimovsk, Klin, Krasnogorsk, Krasnoznamensk, Leninsky district (pos. Fork, der. Poynino), Losino-Petrovsky, Lytkarino, Lyubertsy, Mytishchi, Naro-Fominsky district, Noginsk, Pavlovsky Posad, Peresvet, Podolsk and Podolsky district, Ramensky district (pos. Ostrovka), Troitsk, Fryazino, Khimki, Czechovwood, Serpukhov and Serpukhov district , Solnechnogorsk and Solnechnogorsky district, Elektrostal. In the regions of Russia, the house of the Model series P-111M is built in Tver, Tula, Tula region and Kostroma.
The demolition of the house of this series is not subject to, overhaul (sanitation) based on the current standards is not required.
The house of the P-111M (111-M) series (111m) differ outwardly differ from the predecessor - the P-101 series by the presence of rounded balconies, as well as increased apartments and large numbers of various variants of phased plans.
Until the mid-2000s. The buildings of different manufacturers were assigned the number of sinuses: 111m-480, 111m-198, etc.
In the Moscow Territorial Construction Catalog (MTCK), all type block sections of the P-111m series are noted, the most common of which are: 111m-01/17, 111m-15 / 17.1 (row 6-step with a set of apartments 2-1-1-2 ), 111m-02/17, 111m-16 / 17.1 (row 8-step with a set of apartments 3-2-2-3), 111m-03/17, 111m-04/17, 111m-15 / 17.2 (end 7 -SHAs with a set of apartments 2-3-3), 111m-17 / 17.1 (swivel with a set of apartments 1-3-1).
The houses of the 111m series are often built for social needs, with full finish apartments. In 2001, a draft standard series of panel-brick houses was developed on the basis of the P-111m series.
Detailed features of the series
| Passages | from 1. |
| Floors | from 9 to 19, the most common option is 17. The first floor is usually residential |
| Ceiling height | from 2.6 to 2.8 m. |
| Lifts | One passenger (400 kg.) And one cargo-passenger (630 kg.). |
| Balconies | In all apartments. From the mid-2000s. In Moscow and most cities, balconies glazed by the developer. |
| Apartments on the floor | from 3 to 6 |
| Years of construction | from 1996 to the present. time |
| Built houses | about 280. |
| Square of apartments | 1-room apartment Total: 41-53 m², living: 18-21 m², kitchen: 8.1-12 m² 2-room apartment Total: 56-72 m², living: 31.5-40 m², kitchen: 8.7-14.8 m² 3-room apartment Total: 71-96 m², living: 43-55 m², kitchen: 11.6-13.2 m² 4-room apartment Total: 91-106 m², living: 54-60 m², kitchen: 11.6-16 m² |
| Bathrooms | Separate in all apartments. Baths: Standard. In three- and four-room apartments for two bathrooms. |
| Stairs | Unspecified, with a common fire fighting balcony. |
| Garbage chute | With a loading valve on the site |
| Ventilation | Natural and forced exhaust, in the kitchen and bathroom. |
| Walls and overlaps | The outer walls are three-layer (ceramzite concrete or brick + insulation + reinforced concrete panel), a thickness of 30-40 cm. Internal walls - reinforced concrete thickness 16-20 cm. Partitions - Gypsum-concrete, 8 cm thick. Overlapping - reinforced concrete round-mounted stoves 14-16 cm thick. |
| Bearing walls | Transverse and longitudinal domestic reinforced concrete, as well as outdoor end. |
| Colors and cladding | Colors: Dark red, red with sandy, sandy (brick), white, gray, beige, burgundy, brown (tile), whole color gamut (plaster). Facing: Finishing with natural brick (manufacturer KZHI-100), cladding with large-sized tiles (Ukri-480) or plaster (etc. Manufacturers). |
| Type of roof | Flat. Some buildings of the top floor balconies have a visor |
| Dignity | The house of the P-111m (111m) series (111m) has increased thermal insulation, comply with the latest requirements of the Gosstroy of the Russian Federation for energy saving in residential buildings. In the new buildings of the P-111m series (111m), double-glazed windows are installed in wooden frames. |
| disadvantages | |
| Manufacturer | Former construction enterprises of the Ministry of Defense: 480 kg, 100 kg (in the present. Time is included in the Peak Group of Companies), Ukri №198, Doao "179 PSK", 607 UNR (included in GVSU "Center"), Doao "183 Mechanical Plant" , Glavpromstroy, 494 UR |
| Designer | 53rd Central Design Institute of the Ministry of Defense of the Russian Federation, TsNIIEP Housing. |
Homes of the series P-111M large-pointed, panel brick residential buildings. The construction of the series comes from 1996 to the present. Through the use of various materials for the structure of the outer walls, it is possible to avoid the depressurization of interphaline junctions on the facade of the building, which are the Achilles fifth of the panel houses. This series has a modification - panel-brick houses C-222 (from 2001 by N.V.).
The designer is the 53rd Central Design Institute of the Ministry of Defense of the Russian Federation, TsNIIEP Housing. Initially, the series was designed for the needs of the Ministry of Defense. It has various options for typical block sections: 111m-01/17, 111m-15 / 17.1 (in-line 6-step with a set of apartments 2-1-1-2), 111m-02/17, 111m-16 / 17.1 (inline 8 - Half with a set of apartments 3-2-2-3), 111m-03/17, 111m-04/17, 111m-15 / 17.2 (end-step 7-step with a set of apartments 2-3-3), 111m-17 / 17.1 (swivel with a set of apartments 1-3-1). Sometimes at home of the P-111m series build for social needs, with full finish apartments.
Flower range of outdoor walls. Diverse: dark red, red with sandy, sandy (brick), white, gray, beige, burgundy, brown (tile), whole color gamut (stucco). Finishing with natural brick, facing by large-sized tiles or plaster.
In the houses of the P-111m series, the number of floors varies from 9 to 19. The first floor is most often residential. The number of entrances from 1 or more. Each entrance has elevators: one passenger carrying capacity of 400 kg. And one cargo-passenger lifting capacity of 630 kg. The number of apartments on the floor varies from 3 to 6. In one-room apartment living area 18-21m², kitchen 8-12 m²; in two-room residential 31-40 m², kitchen 8-15 m²; In three-room residential 43-55 m², kitchen 11-13 m²; In four-room residential 54-60 m², kitchen 11-16 m². There are two-tier apartments. Many dwellings have dark rooms / storerooms.
The bathroom is separate in all apartments, in three- and four-room has an additional toilet.. Baths: Standard, 170 cm long. Ventilation is a natural exhaust through the ventblocks (bathroom and kitchen). Balconies in all apartments, are glazed at the expense of comforters since 2004 Some buildings of the top floor balconies have a visor. The garbage chute is located in a separate mini-tambone with a loading valve. Stairs have access to a common balcony.
Internal interciano walls - reinforced concrete panels without insulation thickness 16-20 cm thick. Outer walls - three-layer with insulation: an outer layer with a thickness of 8 cm, 14 cm from frost-resistant ceramzite concrete or brick, a medium layer with a thickness of 10 cm, 12 cm, 15 cm (heat insulating plates from Mineral wool and / or polystyrene foam), the inner layer thick for self-supporting panels 7 cm, for carrier panels 12-17 cm. The total thickness of the outer panels is 30-40 cm. The partitions are dry-concrete 14 cm. Overlapping - 8 -16 reinforced concrete plates with a thickness of 14 -16 cm. Bearing walls are internal reinforced concrete, outdoor end.
Advantages: have increased thermal insulation, meet the latest requirements of the Gosstroy RF energy saving in residential buildings. In the new buildings of the series, double-glazed windows are installed in wooden frames. Many buildings provide ramps and disabled lifts. The manifold of planning apartments, various options for the design of facades (crushed balconies appeared), increased apartments area. Disadvantages: In individual buildings, not very good installation of the outer walls.
Series of panel housesP-111M. the list of demolished does not include, the probability of demolition is even in the long run.
Wall Material: Panel, In Separate Cases (111m-100 Modification) Outer Layer of Brick Wall
Number of sections (entrances): from 1
Number of floors: 9-19, the most common option - 17. The first floor is usually residential
Ceiling height: 2.60 m. - 2.80 m.
Elevators: Framesazhires 630 kg. and passenger 400 kg.
Balconies: in all apartments. From the mid-2000s. In Moscow and most cities, balconies are glad by the developer
Number of apartments on the floor: 3 (in the angular sections), 4, 5, 6
Year of construction: since 1996. time
Areas of construction of panel houses of the P-111m series (111m) in Moscow: Nikulino, Khodynskoye field, Kuntsevo, Goljanovo, Textiles, Lublin, Printers, Turillavo, Zhulebino, South Butovo. As a rule, the houses of this series are built on the former lands of the Ministry of Defense. Also in a number of Dr. regions of Moscow (Konkovo, Zyuzino) of the 111m series at home are built point. Currently, in Moscow, the houses of this series in Moscow are not built
In the suburbs of the new buildings of the P-111m series (111m) built / built in the cities: Balashikha, Voskresensk, Golitsyno, Dedovsk, Dmitrov, Dolgoprudny, Domodedovo, Dresna, Railway, Zvenigorod, Klimovsk, Klin, Krasnogorsk, Krasnoznamensk, Leninsky district (pos . Formation, der. Pyhinino), Losino-Petrovsky, Lytkarino, Lyubertsy, Mytishchi, Naro-Fominsky district, Noginsk, Pavlovsky Posad, Peresvet, Podolsk and Podolsk district, Ramensky district (pos. Islets), Reutov, Serpukhov and Serpukhovsky district, Solnechnogorsk and Solnechnogorsky district, Troitsk, Fryazino, Khimki, Chekhov, Elektrostal
The number of houses built in Moscow: about 50, in the Moscow region (including under construction) - about 230. In the regions of the Russian Federation, the house of the P-111m standard series is built in Tver, Tula, Tula region and Kostroma
Square of 1-room apartments: total: 41-53 square meters. m., living: 18-21 square meters. m., Cuisine: 8.1-12 sq. M. m.
Square 2-room apartments: total: 56-72 square meters. m., living: 31.5-40 square meters. m., Cuisine: 8.7-14.8 square meters. m.
Square of 3-room apartments: total: 71-96 square meters. m., living: 43-55 square meters. m., Cuisine: 11.6-13.2 square. m.
Square of 4-room apartments: total: 91-106 square meters. m., living: 54-60 square meters. m., Cuisine: 11.6-16 square meters. m.
All rooms in the apartments of the houses of the P-111m series (111m) isolated. All apartments have dark rooms (pantry)
Demolition of the house of this series are not subject to, overhaul (sanations) based on the current standards do not require
Bathrooms: separate, in 3- and 4-room there is an additional toilet. Baths: Standard, 170 cm long.
Ladders: Unclear, with access to a common balcony. Garbage: Located in a separate mini-tambone, with a loading valve on each floor
Type of kitchen plate: electric
Walls: external three-layer with insulation: an outer layer with a thickness of 8 cm, 14 cm from frost-resistant ceramzite concrete or brick, a medium layer with a thickness of 10 cm, 12 cm, 15 cm (thermal insulation plates from mineral wool and / or polystyrene foam), inner layer thick for self-supporting panels 7 cm, for carrier panels 12-17 cm. The total thickness of the outer panels is 30-40 cm.
Internal intercommmary bearing walls are reinforced concrete without insulation, 16 cm thick and 20 cm. Partitions - gypsum-concrete thickness 8 cm. Overlap - large-sized reinforced concrete slabs with a thickness of 14 cm and 16 cm.
Bearing walls: Domestic reinforced concrete, outdoor end
Section type (entrances): Tower (only in modifications of P-111-355 2), end, row (ordinary), angular (swivel)
Number of steps in the section (entrance): 6 (set of apartments 2-1-1-2, row sections), 7 (set of apartments 3-2-2, 2-1-2-3, row sections), 8 (set of apartments 2-3-3-2, 2-2-1-1-1-1, row sections), 10 (tower sections). Set of apartments in the end sections: 2-2-3, 1-2-3 or 1-3-1. The width of the longitudinal and transverse step (the distance between two adjacent carriages, the width of the span of the overlap): 150 cm., 300 cm., 450 cm. Case width: 15 m., 16.5 m.
Facing, coating of outer walls: finishing with natural brick (manufacturer KZHI-100), cladding with large-sized tiles (Ukri-480) or plaster (etc. Manufacturers)
Options for external wall flowers: dark red, red with sandy, sandy (brick), white, gray, beige, burgundy, brown (tile), whole color gamut (stucco)
Roof type: flat. Some buildings of the top floor balconies have a visor
Distinctive features: The house of the P-111M (111-M) series (111-M) is extortable from the predecessor - the P-101 series by the presence of rounded balconies, as well as increased apartments and large numbers of various options for floor plans.
Advantages: The house of the Model series P-111M (111M) has increased thermal insulation, comply with the latest requirements of the RF power saving in residential buildings. In the new buildings of the P-111m series (111m), double-glazed windows are installed in wooden frames. Many buildings provide ramps and disabled lifts
Manufacturers - former construction enterprises of the Ministry of Defense: 480 KZhi, 100 KZhi (in the present. Time is included in the Peak Companies Group), Ukri №198, Doao "179 PSK", 607 UNR (entering GWS "Center"), Doao "183 Mechanical Plant », Glavpromstroy, 494 UR
Designers: 53rd Central Design Institute of the Ministry of Defense of the Russian Federation, TsNIIEP Housing. Initially, the series was designed for the needs of the Ministry of Defense, in a number of sources appears the name P-111mo, and in separate military projects - KPD-111m. Until the mid-2000s. The buildings of different manufacturers were assigned the number of sinuses: 111m-480, 111m-198, etc.
In the Moscow Territorial Construction Catalog (MTCK), all type block sections of the P-111m series are noted, the most common of which are: 111m-01/17, 111m-15 / 17.1 (row 6-step with a set of apartments 2-1-1-2 ), 111m-02/17, 111m-16 / 17.1 (row 8-step with a set of apartments 3-2-2-3), 111m-03/17, 111m-04/17, 111m-15 / 17.2 (end 7 - Honey with a set of apartments 2-3-3), 111m-17 / 17.1 (swivel with a set of apartments 1-3-1)
The houses of the 111m series are often built for social needs, with full finish apartments. In 2001, on the basis of the P-111m series, a draft model series of panel-brick houses C-222 was developed.
Photos from sites www.gunai.ru, www.pik.ru, www.unr494.ru
Greeting you! This material contains information about the houses of the P-111m series and in particular, balconies. We will consider issues related to work on waterproofing and insulation, as well as the most popular types of materials. Special attention will be paid to sliding and swing windows installed on the balconies. We will look at the main differences, features and advantages.
You will learn how work is performed on the combination of balconies with a kitchen and a room, which materials are needed for the inner and exterior decoration. Pictures of projects made by our masters are collected in the photo gallery. The video will introduce you to the features of insulation. In a separate unit, information about furniture embedded in the balconies is presented. Features of the glazing of the loggia of P-111M with swing windows
For maximum thermal insulation of LOGGIA P-111M, windows from PVC profile are used. The market presents products of various manufacturers, but the most popular windows of the KBA and REHAU are most popular. Rehau Blitz 60's profile is characterized by an optimal value ratio of price and quality, Kve's window profile. Energy 70 provides better thermal insulation.
The main advantages of warm glazing: good thermal insulation, durability, windows do not require special care, there is the possibility of choosing the optimal type of window profile and a glass package.
Loggia features: semicircular shape. Features of metal-plastic windows: a large mass (in comparison with swing window systems), higher cost. In our photo gallery, you can see examples of glazing balconies by window systems from PVC profile.
Sliding glazing of loggia P-111M
Sliding windows are the optimal solution for balconies that are not used as a residential premises. Advantages of sliding window systems: Saving free space (thanks to sliding skeins), low weight, practicality, durability (more than 20 years of impeccable service).
Features of sliding glazing: sash provide good protection from wind, snow and rain - the high-quality insulation of the room they cannot provide. Remember that the temperature difference in the room and on the street is no more than 10-15 degrees. Another important point - aluminum flaps at minus temperatures can voic. The result of such a phenomenon - it is not always possible to open windows for venting in winter.
Windows Sladonds made of plastic is deprived of such a shortage. In the photos, you can see examples of glazing balconies with sliding window systems.
The P-111m loggia is distinguished by a non-standard shape and equipped with an erker. List of works performed: glazing, vaporizoation with foil foam, internal turnkey trim, installation of the balcony unit, replacing electrical wiring and lighting. The loggia is glazed by sliding windows of the craws from the aluminum profile.
On the video - glazing of loggia P-111M sliding windows turnkey
Popular Materials for Warming Loggia P-111M
In the houses of the P-111m series, a large balcony that can be used to increase apartment living space. In order to equip an extra room on the balcony, a complex of work on heat and waterproofing is required. There are a large number of insulation - in this block we will look at the most popular and affordable options.
The most common insulation is the penplex. This material is dense sheets of orange color with a thickness of 30, 40 or 50mm. The higher the thickness of the material, the more high-quality thermal insulation it provides. The choice of thickness is carried out individually. Advantages of the foster means: low weight, attractive cost, good thermal insulation indicators.
Polyurethane foam is no less common. The advantages of polyurethane foam: good thermal insulation, increased rigidity, increased rigidity (if we compare this indicator with the penplex).
Among the most attractive insulation are most attractive to the most attractive foam. This white material, produced in sheets of various thicknesses. The advantages of foam: affordable price, provides good thermal insulation, has a slight weight. Disadvantages - fragility (sheets are easily broken under load).
What materials are used for waterproofing? The most demanded foil foam. It comes in rolls - the wizard sliced \u200b\u200bsliced \u200b\u200bpieces of the desired size. Poinophol should be stacking into the joint (the presence of the adhesive is unacceptable). All seams are carefully sicked with a scotch of aluminum foil.
Our photo gallery presents examples of LO-111M loggias, warmed by the above materials. The video makes it possible to get acquainted in detail with the peculiarities of our insulation technology. A similar technology is used in the insulation of a loggia of P-111M turnkey
Video insulation of loggia by penplex and turnkey foam
Overview of materials for the interior decoration of loggias P-111M
Interior decoration is one of the important elements of the integrated repair of loggias P-111M. When choosing materials, the type of glazing is taken into account. If the sliding windows are installed, you should select an inner finish, resistant to humidity and temperature drops. With glazing premises with windows from PVC profile, there are no such restrictions.
The most popular option is plastic panels. Advantages: Attractive appearance, available cost, practicality, low weight, large selection of colors.
No less popular finishing material - wooden lining. The advantages of the lining: made of wood (environmentally friendly raw materials), original drawing of a natural tree, a long service life. Features lining: the price depends on the class (the most expensive Eurovantia, the cheapest - class C).
For the interior decoration of the LOGGIA P-111M, MDF panels are used. Advantages: Low price, simplicity of mounting, variety of patterns and colors (the picture often simulates more expensive types of finishes). Disadvantages - panels poorly tolerate high humidity.
To finish the loggia, you can use ornamental and natural stone. The advantages of such a finish: durability, beautiful appearance, the possibility of combining several finishing materials.
The photos present examples of the finishing of the LOGGIA P-111M above the materials listed.
We present to your attention the finishing with plastic panels of the plastic loggia P-111M turnkey. For the interior decoration of the loggia, plastic panels are applied with a tree pattern. On the floor of the loggia laid dark - brown laminate.
Video Finishing Loggia P-111M Plastic Turnkey Panels
Combining Loggia P-111M with room and kitchen
It is possible to enlarge the living area of \u200b\u200bthe apartment at the expense of the balcony. The most attractive and affordable method is to combine a balcony with a room or kitchen. Advantages of combination: Additional meters of living space, the possibility of arranging a separate room, the possibility of zoning the balcony (separate area for recreation and work), a variant of the removal of large household appliances (for example, a refrigerator) and furniture is possible.
Please note: when combining a balcony with a room or kitchen, the supporting structures of the house are not affected. Masters remove only a balcony block. Therefore, the permission of BTI and other state bodies is not required. Photos in our gallery clearly demonstrate examples of combination and the results obtained.
We present an example of aligning a loggia with a kitchen. The object is an aircraft loggia in the P-111m series. Combining a loggia with a kitchen carried out without disassembling bearing walls. Only a balcony unit was dismantled: part of the wall under the windowsill and the threshold remained intact. The arker part of the loggia was isolated by a plastic door - the Erker turned into a small and well-groomed storage room. Loggia replaced electrical wiring and compact lamps are installed. The loggia is heated by a modern heating system - infrared warm floors.
Video alignment of loggia P-111M with turnkey kitchen
Built-in furniture for loggia P-111M
Loggia space P-111M can be adapted for storage of things. In order to save a free area, the furniture of compact sizes, made from a variety of materials. It may be an inexpensive chipboard or natural wood with expensive finish types.
Before proceeding with the manufacture of furniture, it is necessary to determine its purpose. For the storage of outerwear, more free space will be required for small items - more shelves. The most popular types of furniture for the balcony are cabinets and cabinets of various sizes.
How to reduce the cost of furniture? For this, the side and rear walls are removed. Such changes significantly reduce the cost of the finished product, and do not affect the quality of furniture and its service life. The photo gallery presents examples of such furniture made for the P-111m loggia.
For the loggia, an individual project was made of built-in furniture to order. This is a wardrobe of a laminated chipboard and compact stand. In the process of manufacturing built-in furniture, all the requirements and wishes of the customer were taken into account, and the color gamut of the built-in furniture corresponds to the loggia interior.
Video of built-in furniture for loggia P-111M to order
A series of houses P-111m Balcony glazing
For glazing balconies in the P-111m series, sliding and swing windows are used. The PVC profile windows provide maximum thermal insulation. The REHAU BLITZ 60 and KBE expert 70 profile is most often used.
Sliding windows are used to protect the balcony from rain, snow and wind. It should be remembered that the temperature in the room will differ from the street indicators of only 10-15 degrees. The most popular products of Provedal and Krauss companies (aluminum window profile) and Slideshors (plastic profile) indicated on the price page are approximate.
You will be able to find out the exact information only after the balcony is performed and the glazing type is selected. Do not forget that aluminum swollen windows at minus temperatures can freeze. There is no such lack of plastic windows Sladors.
Glazing Type - Sliding System: Krauss or Provedal
Sample balcony size - 2300x1400x600x600. price 28800 rub
Glazing Type - Sliding System: Slidors
Sample balcony size - 2300x1400x600x600. price 31 334 rub
Glazing Type - Swing System: KBE
Sample balcony size - 2300x1400x600x600. price 35 500 rub
P-111m House Series P-111m Apartment Ply
The P-111M series is large houses made from concrete panels, with beautiful loggias, balconies and erkers. Particular attention to the architects paid out appearance: the facade is often decorated with decorative belts, fronts and light structures.
Round-shaped balconies are one of the distinguishing features of the series. The construction of houses of the P-111m series began in 1996 and continues until today. On the territory of Moscow, at home can be seen in such areas: Nikulino, the Khodyan field, Kuntsevo, Goljanovo, textiles, Lublin, Printers, Biryulyvo. In the suburbs: Balashikha, Resurrection, Golitsyno, Dedovsk, Dmitrov, Dolgoprudny, Domodedovo, Dresna, Railway, Zvenigorod.
Specifications Series: Floors - 9-19, ceilings height - 280mm, there is a passenger and cargo-passenger elevators in the entrance, each apartment has balconies, which since 2004 are glazed directly by the developer. The outer walls are made of 3 layers with insulation inside. The middle layer consists of polystyrene foam, outdoor, 14cm thick - from a ceramzite concrete. Internal walls with a thickness of 20cm are made of reinforced concrete.
Bearing structures - all external walls. Internal intercorporation reinforced concrete walls. Facing - natural brick or plaster.
The advantages of the series: excellent thermal insulation corresponding to modern standards, the presence of ramps for disabled, high ceilings, modern planning of apartments. Disadvantages - in separate buildings there is an unsatisfactory quality of wall mounting.
Calculation of the price of glazing apartments in the house of the P-111M turnkey series
Four bedroom apartment - Dimensions and prices of windows
the price is formed
Three room flat - Dimensions and prices of windows
Profile Rehau Blitz (Blitz) 60 - the price is formed
Two-roomed flat - Dimensions and prices of windows
Profile Rehau Blitz (Blitz) 60 - the price is formed
One bedroom apartment - Dimensions and prices of windows
Profile Rehau Blitz (Blitz) 60 - the price is formed
In our work, we use high-quality, safe and most effective technology. The low price of our services is possible thanks to the wholesale purchase of inexpensive and high-quality materials. If you are interested in any of the examples presented, our masters gladly implement it on your loggia or balcony. This concerns the quality of work, then our masters do not like to brag about their success. We offer to familiarize yourself with customer feedback and make your own opinion.
Customer feedback on the repair of the balcony made by our masters. To protect against cold, high-quality PVC profile windows were installed, work on heat and waterproofing were performed.
Plastic panels are used for the interior decoration of the balcony. As a heating system, a warm floor of Caleo was used. To decorate the floor, our masters used laminate. For storage of things on the balcony there is a compact cabinet. One-bedroom apartment has become more spacious, and the balcony has become a functional and warm room.
Note:
Prepayment for the performance of work is only 10%. If you do not have the necessary amount for repair, finishes or glazing balconies, we are ready to provide credit or installment payment
. For all questions that concern lending, please contact our managers.
